1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. jhenager1
    Post

    Solved Stopped printing from SD card

    I have a newed appreciation for the Robo after struggling with the knockoff Kossel I got. They are sending me another mainboard, but compared to...
    Post by: jhenager1, Dec 2, 2016 in forum: Troubleshooting
  2. jhenager1
    Post

    Solved Stopped printing from SD card

    It might be bad form to reply to myself on a Solved thread but I am so excited that I got the strange problem figured out and then got brave in...
    Post by: jhenager1, Dec 2, 2016 in forum: Troubleshooting
  3. jhenager1
    Post

    Solved Stopped printing from SD card

    Post by: jhenager1, Dec 2, 2016 in forum: Troubleshooting
  4. jhenager1
    Post

    Solved Stopped printing from SD card

    Yes.
    Post by: jhenager1, Oct 26, 2016 in forum: Troubleshooting
  5. jhenager1
    Post

    Solved Stopped printing from SD card

    Hey, thanks for the advice. I really do plan on giving the LCD controller another go, but right now, I need to keep printing. What I did was...
    Post by: jhenager1, Oct 26, 2016 in forum: Troubleshooting
  6. jhenager1
    Post

    Solved Stopped printing from SD card

    Yes, bed and extruder heat up fine, and am printing a part right now. SD card reader just quits after about 1-2 seconds. I also noticed I have...
    Post by: jhenager1, Oct 26, 2016 in forum: Troubleshooting
  7. jhenager1
    Post

    Solved Stopped printing from SD card

    Yes, this is the stock card reader. I do have an LCD that I might try to setup. Thanks.
    Post by: jhenager1, Oct 25, 2016 in forum: Troubleshooting
  8. jhenager1
    Thread

    Solved Stopped printing from SD card

    Yesterday, I went to print the final part of a 31 piece assembly, and noticed it did not start heating up the bed after 4 seconds like it has been...
    Thread by: jhenager1, Oct 25, 2016, 18 replies, in forum: Troubleshooting
  9. jhenager1
    Thread

    What model NEMA 17 stepper motor should I get?

    I'm putting together a replacement extruder assembly and want to do a direct swap in case I need to go back to the original, but did not realize...
    Thread by: jhenager1, Sep 2, 2016, 7 replies, in forum: Mods and Upgrades
  10. jhenager1
    Thread

    Looking for a used stock X-carriage

    My hotend will no longer stay in the extruder holder due to the very poor design of having metal screws secured in plastic. After several...
    Thread by: jhenager1, Aug 11, 2016, 4 replies, in forum: Mods and Upgrades
  11. jhenager1
    Thread

    Printing replacement stock hotend part

    Does anyone have a STL for the part right on top that has the two springloaded screws? I have worn a big hole in one side. I think I can fix it...
    Thread by: jhenager1, Jul 30, 2016, 1 replies, in forum: Mods and Upgrades
  12. jhenager1
    Post

    Solved heat bed stopped heating

    Took it all apart again and found nothing loose or disconnected, but now got heat. Thanks anyway!
    Post by: jhenager1, Jul 28, 2016 in forum: Troubleshooting
  13. jhenager1
    Thread

    Solved heat bed stopped heating

    I was printing last night and it looked great and since it was working from the SD card, I went to bed and checked about 3 AM and it was almost...
    Thread by: jhenager1, Jul 28, 2016, 2 replies, in forum: Troubleshooting
  14. jhenager1
    Post

    fan specs for hexagon hot-end?

    Started having trouble printing and discovered this fan was not running. Too small to disassemble and solder the broken joint. If anyone else has...
    Post by: jhenager1, Jul 23, 2016 in forum: General Questions
  15. jhenager1
    Post

    Unresolved loosing connection, cant print from sd card

    Looks like an assembly problem My card reader has those 'ears' on the top. (180 degrees rotated). It is pretty easy to take the bottom plate off...
    Post by: jhenager1, Jul 4, 2016 in forum: Troubleshooting
  16. jhenager1
    Post

    Unresolved loosing connection, cant print from sd card

    Post by: jhenager1, Jul 4, 2016 in forum: Troubleshooting
  17. jhenager1
    Post

    Unresolved COM3 is in use

    Thanks. I will try that also.
    Post by: jhenager1, Jun 12, 2016 in forum: Troubleshooting
  18. jhenager1
    Post

    Unresolved COM3 is in use

    I will try that again. I have deleted it and updated the driver several times, but whatever it takes. I am accustomed to imposing my will on...
    Post by: jhenager1, Jun 12, 2016 in forum: Troubleshooting
  19. jhenager1
    Post

    Unresolved COM3 is in use

    Yes, it is showing as being on COM3 in Device Manager.
    Post by: jhenager1, Jun 12, 2016 in forum: Troubleshooting
  20. jhenager1
    Post

    Unresolved COM3 is in use

    I did because at one point it would not add, and I saw it was unplugged. Plugged it in, and it showed up on COM3. One thing I am not sure about...
    Post by: jhenager1, Jun 12, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2