1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 10
  1. Wesley Knapp
    Thread

    LCD Controller question

    If I use the Pause feature on the controller, can I then raise the printhead, swap out filament and then Resume? When it resumes will it move...
    Thread by: Wesley Knapp, Jun 24, 2020, 11 replies, in forum: Mods and Upgrades
  2. Lucas Siegle
    Thread

    Scrolling Text on LCD

    So I have LCD Controller XXL on Robo 3D r1 Printer, and I was wondering if there is a way to make the text/gcode file names on the sd card that...
    Thread by: Lucas Siegle, Jul 26, 2019, 1 replies, in forum: Mods and Upgrades
  3. Aaron C.
    Thread

    XXL lcd controller

    Looking to buy LCD controller, but need to get it off Amazon. Anyone able to point me at some good controllers on there similar to the XXL one...
    Thread by: Aaron C., Dec 30, 2016, 4 replies, in forum: Mods and Upgrades
  4. coombs
    Thread

    XXL LCD problem

    Hello, I got the XXL LCD and hooked it up to my Robo 3D R1 and it just displays two black lines. Nothing else. I checked the firmware an it is...
    Thread by: coombs, Dec 9, 2016, 2 replies, in forum: Mods and Upgrades
  5. Wesley Knapp
    Thread

    LCD Controller Kill Button

    ...used on many of the printable bezel/cases for the reprapdiscount LCD controller boards. You guessed it - I bumped the button at hour 12 of a...
    Thread by: Wesley Knapp, Jan 29, 2019, 1 replies, in forum: Mods and Upgrades
  6. brandt
    Thread

    reprad smart lcd display

    ...and I have had a lot of fun with it but I am trying to install a lcd smart display I got it from printedsolid it was an older one and has mg1...
    Thread by: brandt, Mar 6, 2017, 10 replies, in forum: Mods and Upgrades
  7. Malte
    Thread

    Full Graphics Lcd Controller

    HEy, i bought a lcd controller for the robo and i plugged it in. But the text didnt show, so i went to arduino and removed the // for the full...
    Thread by: Malte, Jul 13, 2016, 17 replies, in forum: Mods and Upgrades
  8. DJ Sterrett
    Thread

    Smart LCD Controller XXL jibberish

    My LCD XXL starts out good with the information on it and then mid print all the words turn to jibberish (see pic). The print still prints...
    Thread by: DJ Sterrett, Dec 12, 2017, 11 replies, in forum: Mods and Upgrades
  9. Gripp
    Thread

    Full Graphics LCD Smart Controller

    ...Robo R1+ and I'm starting to figure things out on it. I installed an LCD controller but the screen turns on blank. I looked into it a bit and...
    Thread by: Gripp, May 3, 2017, 6 replies, in forum: Mods and Upgrades
  10. PrintedScript
    Thread

    Where to get LCD Mod 2024

    ...are a few drawbacks for me. One of those downsides is not having an lcd controller. I know that there were a number of LCD mods such as the...
    Thread by: PrintedScript, Mar 22, 2024, 2 replies, in forum: Mods and Upgrades
  11. RoboticsRob
    Thread

    New source for reprapdiscount XXL LCD controller?

    Does anyone have a new source for the reprapdiscount XXL LCD controller? I confirmed with printed solid that they will not be carrying it any...
    Thread by: RoboticsRob, Apr 9, 2019, 4 replies, in forum: Mods and Upgrades
  12. Patrick Ryan
    Thread

    lcd/ printer freezing up after I connect to computer

    ...mesh. Everything loaded fine and the printer functions fine from the lcd by itself but I am unable to run the PID autotune.i have tried...
    Thread by: Patrick Ryan, May 4, 2017, 15 replies, in forum: Mods and Upgrades
  13. danzca6
    Thread

    Custom Boot Screen for Marlin and Full Graphics LCD

    ...pretty straight forward. Things needed: A RepRap Full Graphics LCD Controller A way to create a BMP file. I use Paint.NET which is free found...
    Thread by: danzca6, Dec 8, 2016, 2 replies, in forum: Mods and Upgrades
  14. joea
    Thread

    LCD (or other) control panel. Mainly for filament change.

    In other treads I have seen mention of changing filament in mid print. As I looked into that, seems a Control Panel might be a reasonable way...
    Thread by: joea, May 2, 2020, 30 replies, in forum: Mods and Upgrades
  15. Wesley Knapp
    Thread

    New thread for R1+/ReprapDiscount LCD Smart Controller Setup

    ...to make a change to the firmware: Is this the printer firmware or LCD controller firmware? Where do I find the firmware files to alter &...
    Thread by: Wesley Knapp, Jan 19, 2019, 21 replies, in forum: Mods and Upgrades
  16. NLCarrII
    Thread

    Control Z-Height on LCD XXL Screen During Print

    Hello Forum, I am getting back to using my Robo. I've had it for a few years, and always had issues with the Z-Height calibration and the...
    Thread by: NLCarrII, Jun 21, 2017, 3 replies, in forum: Mods and Upgrades
  17. tonycstech
    Thread

    R1 how to get this LCD to work ?

    ...upgraded my old R1 from RAMPS 1.4 to MKS Gen L 1.0 board leaving same LCD in place. Everything worked fine. I changed to another LCD and now it...
    Thread by: tonycstech, Jun 5, 2023, 38 replies, in forum: Mods and Upgrades
  18. RoboRage
    Thread

    R1+ Upgrade: Marlin 2.0.9.2 config file for BLTouch and E3D V6 (no LCD)

    Attached is the Config file I'm using with Marlin 2.0.9.2. I have installed an E3D V6 hot end and a BLTouch v3.1. I use Arduino IDE 1.8.16 for...
    Thread by: RoboRage, Nov 7, 2021, 0 replies, in forum: Mods and Upgrades
  19. mark tomlinson
    Post

    LCD (or other) control panel. Mainly for filament change.

    Which LCD exactly? Discount or Full Graphic?
    Post by: mark tomlinson, May 14, 2020 in forum: Mods and Upgrades
  20. BrooklynBay
    Post

    RepRap Smart Controller

    https://www.partsbuilt.com/ramps-1-4-lcd-smart-adapter/
    Post by: BrooklynBay, Jul 1, 2021 in forum: Mods and Upgrades
Showing results 1 to 20 of 182 Next >
Search Again
Page 1 of 10