1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 1 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. Russ_B

    Partial Answer Firmware Recommendation

    Russ_B, Sep 25, 2022
    Replies:
    2
    Views:
    709
    Russ_B
    Russ_B
    Sep 27, 2022
  2. joea

    Partial Answer Z_RAISE_BEFORE_HOME

    joea, Aug 19, 2021 ... 2
    Replies:
    32
    Views:
    2,640
    mark tomlinson
    mark tomlinson
    Aug 21, 2021
  3. joea

    Partial Answer Z-axis offset, adjusting.

    joea, Aug 15, 2021 ... 2
    Replies:
    31
    Views:
    3,095
    mark tomlinson
    mark tomlinson
    Aug 21, 2021
  4. Brandon Hines

    Partial Answer Bad Prints, need help!!!

    Brandon Hines, Nov 10, 2020
    Replies:
    4
    Views:
    797
    Brandon Hines
    Brandon Hines
    Nov 10, 2020
  5. joea

    Partial Answer My X and Y steps/mm need to be 160 not 80?

    joea, May 15, 2020
    Replies:
    1
    Views:
    783
    mark tomlinson
    mark tomlinson
    May 15, 2020
  6. PaulusRich1997

    Partial Answer Small Detail Print Gaps Between lines

    PaulusRich1997, Oct 21, 2019
    Replies:
    5
    Views:
    964
    mark tomlinson
    mark tomlinson
    Oct 22, 2019
  7. CCJ

    Partial Answer Firmware Nonresponsive

    CCJ, Sep 15, 2019
    Replies:
    1
    Views:
    694
    mark tomlinson
    mark tomlinson
    Sep 16, 2019
  8. Daniel Flores

    Partial Answer Filament not entering extruder

    Daniel Flores, Sep 2, 2019
    Replies:
    2
    Views:
    829
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  9. Dannny18

    Partial Answer Trouble with printing

    Dannny18, Sep 2, 2019
    Replies:
    1
    Views:
    685
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  10. robert albrecht

    Partial Answer Ughhhh I am back... MC not printing support strucures

    robert albrecht, Aug 21, 2019
    Replies:
    2
    Views:
    802
    BrooklynBay
    BrooklynBay
    Aug 22, 2019
  11. MarchHare

    Partial Answer New R1 (new to me) inherited from a friend. worked for him, non-functional for me. I need help

    MarchHare, Jul 31, 2019
    Replies:
    7
    Views:
    1,000
    MarchHare
    MarchHare
    Aug 1, 2019
  12. mindphunk

    Partial Answer Cooling Issue?

    mindphunk, Jul 30, 2019
    Replies:
    1
    Views:
    712
    mark tomlinson
    mark tomlinson
    Jul 31, 2019
  13. Connor Williams

    Partial Answer Heated bed connector replacement

    Connor Williams, Jun 13, 2019
    Replies:
    9
    Views:
    1,273
    mark tomlinson
    mark tomlinson
    Jun 19, 2019
  14. felipe fomez

    Partial Answer rods bent???

    felipe fomez, Mar 28, 2019
    Replies:
    2
    Views:
    862
    Geof
    Geof
    Mar 29, 2019
  15. Dan McCreary
    Locked

    Partial Answer MatterControl will not run on macOS Mojave 10.14.3

    Dan McCreary, Mar 7, 2019
    Replies:
    1
    Views:
    945
    WheresWaldo
    WheresWaldo
    Mar 8, 2019
  16. Kian Ghassemian

    Partial Answer My R1 is stopping after callibration

    Kian Ghassemian, Feb 27, 2019
    Replies:
    2
    Views:
    648
    mark tomlinson
    mark tomlinson
    Feb 28, 2019
  17. Mark Ostrander

    Partial Answer printer stops ...unable to communicate with printer

    Mark Ostrander, Feb 27, 2019
    Replies:
    1
    Views:
    585
    mark tomlinson
    mark tomlinson
    Feb 27, 2019
  18. Bd182

    Partial Answer Soft edges, higher than the center

    Bd182, Feb 19, 2019
    Replies:
    1
    Views:
    533
    Geof
    Geof
    Feb 19, 2019
  19. Domenic

    Partial Answer Layer lines on my prints are not even

    Domenic, Nov 22, 2018 ... 2
    Replies:
    36
    Views:
    4,056
    TheOneWhoWhelms
    TheOneWhoWhelms
    Feb 1, 2019
  20. xfire_dragonx

    Partial Answer print not original shape in z axis

    xfire_dragonx, Nov 8, 2018 ... 3 4 5
    Replies:
    86
    Views:
    9,076
    mark tomlinson
    mark tomlinson
    Jan 20, 2019
Showing threads 1 to 20 of 113

Thread Display Options

Loading...
Page 1 of 6