1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. banolka
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Where can I get 1.1.3 for R1 with threaded screws?
    Post by: banolka, Jun 9, 2017 in forum: Mods and Upgrades
  2. banolka
    Post

    Solved Bed Leveling Robo3d R1+

    Can someone measure the one on R1+? Then it can be remodeled.
    Post by: banolka, Jun 5, 2017 in forum: Troubleshooting
  3. banolka
    Post

    Solved Bed Leveling Robo3d R1+

    This one is without "hook" like on the R1+ ;/ I was hoping that more detailed one is avalible
    Post by: banolka, Jun 5, 2017 in forum: Troubleshooting
  4. banolka
    Post

    Solved Bed Leveling Robo3d R1+

    is thetre a model for those clipson leveler? I have old one with no support on side;/
    Post by: banolka, Jun 5, 2017 in forum: Troubleshooting
  5. banolka
    Post

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    But how come the mesh is so wrong? It rises way to high the the point on last portion. Is there any option to validate this mesh? Y4 & Y5 position...
    Post by: banolka, May 30, 2017 in forum: Troubleshooting
  6. banolka
    Post

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    So I came back to Marlin 1.1.0-RCBugFix and performed mesh again: Send: M503 Recv: echo:Steps per unit: Recv: echo: M92 X80.00 Y80.00 Z2560.00...
    Post by: banolka, May 30, 2017 in forum: Troubleshooting
  7. banolka
    Post

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    Hmmm can you share repository with order firmware? I'm not sure If I have previous version on computer to reload it back ;/
    Post by: banolka, May 30, 2017 in forum: Troubleshooting
  8. banolka
    Post

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    Ok great. One more thing. In 1.1.0RC8FIX i had lower increments to change in the MESH so it could be more fine tuned where can i add this and PID...
    Post by: banolka, May 29, 2017 in forum: Troubleshooting
  9. banolka
    Post

    Solved No Z-clearance on first layer

    A question. If i use latest Marlin 1.1.1 i should use M565 or M851? Sent from my iPhone using Tapatalk
    Post by: banolka, May 29, 2017 in forum: Troubleshooting
  10. banolka
    Post

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    I did again. however I cannot level MESH via LCD it does not allow me to go over 2.000 and this is not enough to fit paper sheet. any suggestions?
    Post by: banolka, May 29, 2017 in forum: Troubleshooting
  11. banolka
    Thread

    Answered FIRST LAYER Z-OFFSET NOT CORRECT

    Hi, I have following problem. I try to print but 1st layer/layers are not correct. Z-offset is not kept and for some time layers are not building...
    Thread by: banolka, May 29, 2017, 12 replies, in forum: Troubleshooting
  12. banolka
    Post

    Unresolved Bed is dead:/

    What thermistor should i buy? Sent from my iPhone using Tapatalk
    Post by: banolka, May 25, 2017 in forum: Troubleshooting
  13. banolka
    Thread

    Unresolved Bed is dead:/

    Hi, Today i got this error: Thermal Runaway, system stopped! Heater_ID: bed I googled it and it looks like faulty heater thermistor. I think...
    Thread by: banolka, May 25, 2017, 4 replies, in forum: Troubleshooting
  14. banolka
    Post

    Answered Adhesion problem [PLA]

    I have Dimafix - but it needs temp above 50-60C to work. I'll try spray and no heating. I thought that glass and correct layer height would do...
    Post by: banolka, May 5, 2017 in forum: Troubleshooting
  15. banolka
    Thread

    Answered Adhesion problem [PLA]

    Hi, I have Robo 3D R1 with threaded rods, E3D V6, GLASS BED with Marlin 1.1.0 RCFIX with MESH leveling. I have adhesion problem. I set z-offset...
    Thread by: banolka, May 5, 2017, 2 replies, in forum: Troubleshooting
  16. banolka
    Post

    Answered How to readjust the z offset

    I have R1 with E3D v6 Sent from my iPhone using Tapatalk
    Post by: banolka, May 4, 2017 in forum: Troubleshooting
  17. banolka
    Post

    Answered How to readjust the z offset

    I have same problem i use cura 2.3.1 made for robo Sent from my iPhone using Tapatalk
    Post by: banolka, May 4, 2017 in forum: Troubleshooting
  18. banolka
    Post

    Bed upgrade to Mk42 Heated Bed Ultimate 3D Printer Build Plate

    Hmm I was thinking to add aluminium plate instead of glass bed and screw MK42 bed to it. and Connect cables :) I think it would work :) How about...
    Post by: banolka, Apr 12, 2017 in forum: Mods and Upgrades
  19. banolka
    Thread

    Bed upgrade to Mk42 Heated Bed Ultimate 3D Printer Build Plate

    Hi is it possible to use - https://www.indiegogo.com/projects/mk42-heated-bed-ultimate-3d-printer-build-plate/x/6011017#/ in Robo 3d R1? Is it...
    Thread by: banolka, Apr 12, 2017, 6 replies, in forum: Mods and Upgrades
  20. banolka
    Thread

    SilentStepstick installation

    Hi, did anyone updated their stepaticks to TMC2100? I want to lower noise generated by the printer and this is one of my ideas. Wysłane z iPhone...
    Thread by: banolka, Jul 4, 2016, 1 replies, in forum: General Questions
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2