1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

KTMDirtFace's Robo3d

Discussion in 'Show and Tell' started by KTMDirtFace, May 19, 2015.

  1. KTMDirtFace

    KTMDirtFace Well-Known Member

    Joined:
    May 18, 2015
    Messages:
    1,247
    Likes Received:
    461
    Pretty exited about this.

    Printed a camera mount in Sainsmart TPU for my quadcopter, with supports even... So I have tried and tried to print ninjaflex, and I have done it, but this was just so much easier. Yes its not as "noodly" as ninja flex, but it prints good? This was at 30mm/s and no retraction. I think i'm going to try 60mm/s with normal retraction I think the Titan can handle it.

    I put glue stick down on my Frosted Lexan, to make it stick Less.


    [​IMG]

    [​IMG]

    Supports pulled off pretty easy.
     
    Geof, mark tomlinson and WheresWaldo like this.
  2. KTMDirtFace

    KTMDirtFace Well-Known Member

    Joined:
    May 18, 2015
    Messages:
    1,247
    Likes Received:
    461
    Printed this out last night for my Nintendo Switch. I find the Nintendo switch extremely uncomfortable and gives me hand cramps ( I have huge hands ). Found this on thingiverse seems like it will help. It just fit on my robo3d diagonally. like a MM to spare.

    [​IMG]
    [​IMG]
    [​IMG]
     
    Geof, WheresWaldo and Kilrah like this.
  3. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,707
    Likes Received:
    2,314
    lookin good buddy! Nice job!
     
  4. KTMDirtFace

    KTMDirtFace Well-Known Member

    Joined:
    May 18, 2015
    Messages:
    1,247
    Likes Received:
    461
    More random things.. Sister and Nephew visiting, hes like 5. I realized I have never used the bathtub before and have no plug.

    Made this in TPU today.. it works but my printer is definitely do for a new nozzle. Everything is under extruding now. Layers look like a screen rather than solid.
    [​IMG]

    [​IMG]

    Also printed this Star wars soda can koozie
    [​IMG]
     
    WheresWaldo and Geof like this.
  5. KTMDirtFace

    KTMDirtFace Well-Known Member

    Joined:
    May 18, 2015
    Messages:
    1,247
    Likes Received:
    461
    Decided to try to print that switch grip thing ( a few posts up ). In TPU. Because the PETG one I made is pretty slippery in my hands.

    It printed!, however as I expected its too floppy to actually hold the switch lol. But at least I know I can print crazy things in TPU now. all the crazy whisps from no retraction were easy to remove.

    Printed in sainsmart TPU with no retraction 30mm/s..took forever.

    [​IMG]
     
    #125 KTMDirtFace, Aug 18, 2017
    Last edited: Aug 18, 2017
    Geof and mark tomlinson like this.
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    22,430
    Likes Received:
    7,183
    Yea, my initial though was that it looked rather large for a really flexible part :)
     
    KTMDirtFace likes this.
  7. KTMDirtFace

    KTMDirtFace Well-Known Member

    Joined:
    May 18, 2015
    Messages:
    1,247
    Likes Received:
    461
    Have a EVO SS Gimbal, but my go pro session when riding aggressive on Mountain bike hits the gimbal on turns.

    I tried to fix it by printing this to offset the camera further forward like regular hero's sit in the gimbal. Unfortunately this puts it off balance and the motors are not happy. Oh well I can print session mounts now :).. made it in fusion 360

    [​IMG]
    [​IMG]

    Stock, back of camera is close to the gimbal/foam.
    [​IMG]

    3D Printed Offset: To bad it doesnt work, pisses the motors off.
    [​IMG]

    Regular hero's work much better on this gimbal.
    Old Hero 3
    [​IMG]
     
    mark tomlinson likes this.

Share This Page