1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 2 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views ↑
Last Message
  1. Chris Rodriguez

    Partial Answer Failure or unacceptable print rate %

    Chris Rodriguez, Jan 27, 2016
    Replies:
    11
    Views:
    705
    WheresWaldo
    WheresWaldo
    Jan 28, 2016
  2. Russ_B

    Partial Answer Firmware Recommendation

    Russ_B, Sep 25, 2022
    Replies:
    2
    Views:
    714
    Russ_B
    Russ_B
    Sep 27, 2022
  3. momoe

    Partial Answer Whole hot end and heatsync are loose

    momoe, Feb 6, 2017
    Replies:
    1
    Views:
    719
    mark tomlinson
    mark tomlinson
    Feb 7, 2017
  4. mindphunk

    Partial Answer Cooling Issue?

    mindphunk, Jul 30, 2019
    Replies:
    1
    Views:
    723
    mark tomlinson
    mark tomlinson
    Jul 31, 2019
  5. rkohr12

    Partial Answer Heated bed not responding

    rkohr12, Feb 1, 2017
    Replies:
    4
    Views:
    726
    mark tomlinson
    mark tomlinson
    Feb 1, 2017
  6. Frankn

    Partial Answer Why do prints break free?

    Frankn, Sep 11, 2015
    Replies:
    7
    Views:
    730
    William Muraski
    William Muraski
    Sep 14, 2015
  7. Agrijag

    Partial Answer Need help finishing extruder swap

    Agrijag, Jan 28, 2017
    Replies:
    1
    Views:
    742
    mark tomlinson
    mark tomlinson
    Jan 28, 2017
  8. SergeantPepper

    Partial Answer How to identify your Robo3D printer:

    SergeantPepper, Mar 30, 2015
    Replies:
    1
    Views:
    745
    Mike Kelly
    Mike Kelly
    Mar 30, 2015
  9. George Westwater

    Partial Answer Help, strange heated bed issue

    George Westwater, Feb 6, 2018
    Replies:
    3
    Views:
    760
    mark tomlinson
    mark tomlinson
    Feb 23, 2018
  10. Timbiat

    Partial Answer R1+ Print Bed Doesn't Heat

    Timbiat, Nov 27, 2017
    Replies:
    2
    Views:
    782
    Rod Smith
    Rod Smith
    Nov 28, 2017
  11. joea

    Partial Answer My X and Y steps/mm need to be 160 not 80?

    joea, May 15, 2020
    Replies:
    1
    Views:
    786
    mark tomlinson
    mark tomlinson
    May 15, 2020
  12. SLV2NON

    Partial Answer Stumped...

    SLV2NON, Jul 1, 2017
    Replies:
    4
    Views:
    794
    Geof
    Geof
    Jul 5, 2017
  13. Monder

    Partial Answer cannot communicate with the printer

    Monder, Mar 7, 2018
    Replies:
    3
    Views:
    801
    Geof
    Geof
    Mar 8, 2018
  14. robert albrecht

    Partial Answer Ughhhh I am back... MC not printing support strucures

    robert albrecht, Aug 21, 2019
    Replies:
    2
    Views:
    809
    BrooklynBay
    BrooklynBay
    Aug 22, 2019
  15. Brandon Hines

    Partial Answer Bad Prints, need help!!!

    Brandon Hines, Nov 10, 2020
    Replies:
    4
    Views:
    813
    Brandon Hines
    Brandon Hines
    Nov 10, 2020
  16. Daniel Flores

    Partial Answer Filament not entering extruder

    Daniel Flores, Sep 2, 2019
    Replies:
    2
    Views:
    833
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  17. Travis Deel

    Partial Answer Stepper Noise

    Travis Deel, Jul 14, 2015
    Replies:
    5
    Views:
    836
    Mike Kelly
    Mike Kelly
    Jul 15, 2015
  18. Ronny Sharma

    Partial Answer Robo 3D App Crashing on iOS 11.3

    Ronny Sharma, Mar 11, 2018
    Replies:
    2
    Views:
    860
    mark tomlinson
    mark tomlinson
    Mar 11, 2018
  19. Mandinga

    Partial Answer Extruder Alignment and Software Issues

    Mandinga, Jan 27, 2017
    Replies:
    5
    Views:
    865
    Rigmarol
    Rigmarol
    Jan 27, 2017
  20. felipe fomez

    Partial Answer rods bent???

    felipe fomez, Mar 28, 2019
    Replies:
    2
    Views:
    867
    Geof
    Geof
    Mar 29, 2019
Showing threads 21 to 40 of 113

Thread Display Options

Loading...
Page 2 of 6