1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Posts

Page 1 of 3
Title
Replies Views
Last Message
  1. Geof
    Sticky

    Community Favorite Taking the R1+ ramps and rewiring to make generic Ramps Work

    Geof, Apr 22, 2016, Mods and Upgrades ... 4 5 6
    Replies:
    112
    Views:
    24,800
    Jholman05
    Jholman05
    Aug 15, 2020 at 5:59 AM
  2. tkoco
    Locked Sticky

    R2 FAQ

    tkoco, Dec 24, 2019, Troubleshooting
    Replies:
    16
    Views:
    1,674
    tkoco
    tkoco
    Aug 14, 2020 at 7:08 PM
  3. Lance Weston

    Fix for sharp bend in HDMI cable

    Lance Weston, Aug 13, 2020 at 9:35 AM, Mods and Upgrades
    Replies:
    3
    Views:
    53
    Lance Weston
    Lance Weston
    Aug 14, 2020 at 8:47 AM
  4. supercazzola

    Learning to compile the Marlin Firmware - step by step, cause I was a dummy...

    supercazzola, Feb 10, 2018, Troubleshooting
    Replies:
    17
    Views:
    1,986
    tkoco
    tkoco
    Aug 13, 2020 at 5:21 PM
  5. BR3M3RB

    Solved Firmware - Extruder Min Temp - MC

    BR3M3RB, Aug 12, 2020 at 10:05 AM, Troubleshooting
    Replies:
    7
    Views:
    73
    mark tomlinson
    mark tomlinson
    Aug 12, 2020 at 3:12 PM
  6. BR3M3RB

    How to Update Robo firmware with MatterControl

    BR3M3RB, May 21, 2017, Software
    Replies:
    5
    Views:
    1,081
    BR3M3RB
    BR3M3RB
    Aug 12, 2020 at 10:54 AM
  7. BR3M3RB

    Unanswered Best Interface for Robo 3D R1+

    BR3M3RB, Aug 5, 2020, Troubleshooting
    Replies:
    2
    Views:
    167
    BR3M3RB
    BR3M3RB
    Aug 12, 2020 at 10:31 AM
  8. Lance Weston

    R2 stops printing mid print

    Lance Weston, Aug 5, 2020, Troubleshooting
    Replies:
    15
    Views:
    135
    mark tomlinson
    mark tomlinson
    Aug 12, 2020 at 10:03 AM
  9. tiagomaricate

    Calibration cube - the untamed

    tiagomaricate, Aug 10, 2020 at 7:14 PM, General Questions
    Replies:
    4
    Views:
    73
    tiagomaricate
    tiagomaricate
    Aug 12, 2020 at 8:34 AM
  10. DavidR

    linear advance

    DavidR, Mar 14, 2018, General Questions
    Replies:
    13
    Views:
    1,115
    mark tomlinson
    mark tomlinson
    Aug 12, 2020 at 8:33 AM
  11. Carlos Herrera
    Locked

    Robo R2 hot end set screw size

    Carlos Herrera, Jun 10, 2019, General Questions
    Replies:
    3
    Views:
    300
    tkoco
    tkoco
    Aug 12, 2020 at 8:21 AM
  12. BJS227

    print quality is gone

    BJS227, Aug 10, 2020 at 12:43 PM, Troubleshooting
    Replies:
    3
    Views:
    40
    tkoco
    tkoco
    Aug 12, 2020 at 7:48 AM
  13. MGF

    hotend hits the bed

    MGF, Feb 22, 2020, Troubleshooting
    Replies:
    12
    Views:
    390
    tkoco
    tkoco
    Aug 12, 2020 at 7:43 AM
  14. Souless1

    MatterControl support pillars

    Souless1, Jul 28, 2020, General Questions
    Replies:
    3
    Views:
    555
    mark tomlinson
    mark tomlinson
    Aug 11, 2020 at 5:28 PM
  15. tiagomaricate

    No BuildTak Print Surface compatible

    tiagomaricate, Jul 26, 2020, Troubleshooting
    Replies:
    5
    Views:
    99
    tkoco
    tkoco
    Aug 10, 2020 at 11:16 AM
  16. Ave

    Unresolved Unable to print... filament gets stuck

    Ave, Jul 20, 2020, Troubleshooting
    Replies:
    9
    Views:
    238
    mark tomlinson
    mark tomlinson
    Aug 10, 2020 at 10:50 AM
  17. tiagomaricate

    Beep / alarm sound from board

    tiagomaricate, Aug 9, 2020 at 1:29 PM, Troubleshooting
    Replies:
    1
    Views:
    52
    mark tomlinson
    mark tomlinson
    Aug 10, 2020 at 6:13 AM
  18. tiagomaricate

    Can't store the print job on the printer SD card (octoprint and cura)

    tiagomaricate, Aug 8, 2020, General Questions
    Replies:
    6
    Views:
    61
    tkoco
    tkoco
    Aug 8, 2020
  19. tiagomaricate

    Could you help a noob to upgrade the pip?

    tiagomaricate, Aug 5, 2020, Mods and Upgrades
    Replies:
    10
    Views:
    139
    tiagomaricate
    tiagomaricate
    Aug 8, 2020
  20. tiagomaricate

    How can I improve this printing and remove the "waves"

    tiagomaricate, Aug 5, 2020, Troubleshooting
    Replies:
    11
    Views:
    134
    Lance Weston
    Lance Weston
    Aug 8, 2020
Showing results 1 to 20 of 56
Loading...
Page 1 of 3