1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 21 of 26

Filters:

Prefix:
Answered x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. Drmike

    Answered Power supply or overheating?

    Drmike, Feb 15, 2016
    Replies:
    13
    Views:
    2,163
    Geof
    Geof
    Apr 10, 2016
  2. Drmike

    Answered Retraction Formula

    Drmike, Apr 8, 2016
    Replies:
    2
    Views:
    1,061
    Drmike
    Drmike
    Apr 9, 2016
  3. Robert Foreman

    Answered Nozzle size question.

    Robert Foreman, Apr 7, 2016
    Replies:
    3
    Views:
    671
    Robert Foreman
    Robert Foreman
    Apr 7, 2016
  4. invinciblegod

    Answered Print location is different from what is shown in mattercontrol

    invinciblegod, Apr 5, 2016
    Replies:
    9
    Views:
    1,612
    greif07
    greif07
    Apr 6, 2016
  5. I Need Help

    Answered Z axis on ROBO 3D R1 printer is starting print way too high

    I Need Help, Mar 8, 2016
    Replies:
    4
    Views:
    2,049
    I Need Help
    I Need Help
    Apr 4, 2016
  6. Red Submarine

    Answered I need a hexagon hot end fan shroud

    Red Submarine, Feb 6, 2015
    Replies:
    13
    Views:
    2,283
    jediknight0
    jediknight0
    Mar 23, 2016
  7. Robert Foreman

    Answered Are these good auto bed level numbers?

    Robert Foreman, Mar 19, 2016
    Replies:
    6
    Views:
    934
    Robert Foreman
    Robert Foreman
    Mar 19, 2016
  8. garyspring

    Answered Bed Center

    garyspring, Mar 15, 2016
    Replies:
    10
    Views:
    1,664
    Geof
    Geof
    Mar 16, 2016
  9. Arthur Smith

    Answered Which is X Endstop, Y Endstop, and Z Endstop?

    Arthur Smith, Mar 10, 2016
    Replies:
    1
    Views:
    733
    WheresWaldo
    WheresWaldo
    Mar 11, 2016
  10. Arthur Smith

    Answered Wiring help for Adrino after E3D V6 upgrade

    Arthur Smith, Mar 10, 2016
    Replies:
    10
    Views:
    1,398
    mark tomlinson
    mark tomlinson
    Mar 10, 2016
  11. jcman1990

    Answered Thermistor Wires broke

    jcman1990, Mar 9, 2016
    Replies:
    6
    Views:
    1,746
    robert sanchez
    robert sanchez
    Mar 9, 2016
  12. Jimmy Husain

    Answered Overhang?

    Jimmy Husain, Feb 25, 2016
    Replies:
    8
    Views:
    1,722
    Jimmy Husain
    Jimmy Husain
    Feb 26, 2016
  13. Dr. Jack Hirschberg

    Answered Help for a newbie...printer won't home properly

    Dr. Jack Hirschberg, Feb 26, 2016
    Replies:
    3
    Views:
    1,154
    mark tomlinson
    mark tomlinson
    Feb 26, 2016
  14. Rusty

    Answered R1 - Z Axis sensor always triggered

    Rusty, Feb 16, 2016
    Replies:
    9
    Views:
    1,430
    mark tomlinson
    mark tomlinson
    Feb 17, 2016
  15. Kreativekris

    Answered Basic questions for after printing (1st print)

    Kreativekris, Feb 16, 2016
    Replies:
    5
    Views:
    1,049
    LumpyDVC
    LumpyDVC
    Feb 16, 2016
  16. MOwens5150

    Answered Wire harness issue

    MOwens5150, Jan 30, 2016
    Replies:
    5
    Views:
    1,306
    MOwens5150
    MOwens5150
    Feb 2, 2016
  17. Taylor

    Answered Lines in Prints

    Taylor, Jan 29, 2016
    Replies:
    6
    Views:
    1,323
    Taylor
    Taylor
    Jan 30, 2016
  18. JuanPinto

    Answered WIRES CROSSED?

    JuanPinto, Jan 19, 2016
    Replies:
    5
    Views:
    722
    mark tomlinson
    mark tomlinson
    Jan 21, 2016
  19. Travis M

    Answered Print Quality Not Very Good

    Travis M, Jan 2, 2016
    Replies:
    18
    Views:
    1,259
    Geof
    Geof
    Jan 3, 2016
  20. wthierry

    Answered Leadscrew firmware updated, but look what it does...

    wthierry, Dec 30, 2015
    Replies:
    13
    Views:
    1,593
    mark tomlinson
    mark tomlinson
    Jan 3, 2016
Showing threads 401 to 420 of 511

Thread Display Options

Loading...
Page 21 of 26