1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 3 of 26

Filters:

Prefix:
Unanswered x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views ↓
Last Message
  1. Caleb Cangelosi

    Unanswered Where do I plug in my E3D v6 hot end fan?

    Caleb Cangelosi, Dec 20, 2016
    Replies:
    14
    Views:
    2,523
    Toro1966
    Toro1966
    Dec 21, 2016
  2. Kirk
    Locked

    Unanswered Adjust Speed and Print Layer Height During Prints?

    Kirk, Feb 11, 2015
    Replies:
    9
    Views:
    2,511
    mark tomlinson
    mark tomlinson
    Feb 11, 2015
  3. Johndrindak

    Unanswered why cant I add a raft on matter control

    Johndrindak, Mar 16, 2016
    Replies:
    14
    Views:
    2,462
    Kevin Robo 3D
    Mar 18, 2016
  4. JOAQUIN PICCI

    Unanswered No plastic coming out of extruder

    JOAQUIN PICCI, Jul 11, 2015
    Replies:
    15
    Views:
    2,438
    Edwin3d
    Edwin3d
    Jul 13, 2015
  5. Quest

    Unanswered Has this happened to anyone else?

    Quest, Mar 16, 2015 ... 2
    Replies:
    34
    Views:
    2,390
    James Harry
    James Harry
    Jun 2, 2015
  6. ballhogjoni

    Unanswered For some reason the printer stops mid print

    ballhogjoni, Aug 16, 2016 ... 2
    Replies:
    24
    Views:
    2,365
    mark tomlinson
    mark tomlinson
    Aug 19, 2016
  7. Adam King

    Unanswered Help - Everything installed and connected - Robo not responding.

    Adam King, May 30, 2015 ... 2
    Replies:
    27
    Views:
    2,315
    Mike Kelly
    Mike Kelly
    Jun 2, 2015
  8. Cientifico_Loco

    Unanswered Firmware problem

    Cientifico_Loco, Jun 7, 2016
    Replies:
    6
    Views:
    2,305
    Ryan TeGantvoort
    Ryan TeGantvoort
    Jul 14, 2016
  9. erer1243

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    erer1243, May 21, 2016 ... 2
    Replies:
    32
    Views:
    2,247
    Geof
    Geof
    May 22, 2016
  10. nikhil bhansali

    Unanswered Hair spray vs masking tape

    nikhil bhansali, May 19, 2015
    Replies:
    8
    Views:
    2,210
    KTMDirtFace
    KTMDirtFace
    May 20, 2015
  11. chase ashley

    Unanswered Help with Cura Settings

    chase ashley, Feb 11, 2016
    Replies:
    8
    Views:
    2,146
    Mike Kelly
    Mike Kelly
    Feb 17, 2016
  12. joea

    Unanswered Where to set Marlin offset from -X limit for proper "home" position

    joea, Mar 18, 2023
    Replies:
    7
    Views:
    2,144
    mark tomlinson
    mark tomlinson
    Mar 18, 2023
  13. zenekNY

    Unanswered Inconsistent layers, clogs up and keeps going.

    zenekNY, Oct 25, 2015 ... 2
    Replies:
    24
    Views:
    2,111
    zenekNY
    zenekNY
    Oct 29, 2015
  14. sofiadragon1979

    Unanswered Support material question

    sofiadragon1979, Jan 11, 2015
    Replies:
    11
    Views:
    2,053
    jbigler1986
    jbigler1986
    May 11, 2015
  15. Kirk

    Unanswered Simplify 3d make infill speed the same as the Perimeter speed???

    Kirk, May 8, 2015
    Replies:
    1
    Views:
    2,019
    mark tomlinson
    mark tomlinson
    May 8, 2015
  16. Will . I . Am

    Unanswered Spiral "vase" mode on Matter Control

    Will . I . Am, Mar 22, 2017
    Replies:
    1
    Views:
    1,992
    daniel871
    daniel871
    Mar 23, 2017
  17. Jsn9955
    Locked

    Unanswered Can we discuss my calibration cube? Acceptable tolerances?

    Jsn9955, Dec 30, 2014
    Replies:
    10
    Views:
    1,967
    mediaguru
    mediaguru
    Dec 31, 2014
  18. Spencer C

    Unanswered Prints failing after first layers.

    Spencer C, Apr 30, 2015 ... 2
    Replies:
    26
    Views:
    1,967
    RikiDominican13
    RikiDominican13
    May 6, 2015
  19. zenekNY

    Unanswered Robo Calibration for tight part fitment!

    zenekNY, Mar 5, 2016
    Replies:
    19
    Views:
    1,963
    Geof
    Geof
    Mar 7, 2016
  20. Nic Phillips

    Unanswered Adjusting Z Endstop for Leveling?

    Nic Phillips, Apr 6, 2016
    Replies:
    9
    Views:
    1,936
    mark tomlinson
    mark tomlinson
    Apr 7, 2016
Showing threads 41 to 60 of 514

Thread Display Options

Loading...
Page 3 of 26