1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 4 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title ↓ Start Date
Replies Views
Last Message
  1. David Waldron

    Partial Answer Need help with settings print quality

    David Waldron, Feb 19, 2018
    Replies:
    14
    Views:
    2,121
    David Waldron
    David Waldron
    Feb 19, 2018
  2. djokdja09

    Partial Answer Need help for bad quality print (reviving my old Robo3D R1 8mm rod)

    djokdja09, Feb 23, 2017
    Replies:
    3
    Views:
    961
    mark tomlinson
    mark tomlinson
    Feb 24, 2017
  3. Agrijag

    Partial Answer Need help finishing extruder swap

    Agrijag, Jan 28, 2017
    Replies:
    1
    Views:
    736
    mark tomlinson
    mark tomlinson
    Jan 28, 2017
  4. David Waldron
    Locked

    Partial Answer Need help AGAIN please

    David Waldron, Mar 21, 2018
    Replies:
    6
    Views:
    1,132
    BrooklynBay
    BrooklynBay
    Apr 10, 2018
  5. Kieran Davey

    Partial Answer My Z-Axis Is Really, Really Messed Up

    Kieran Davey, Dec 27, 2017
    Replies:
    9
    Views:
    1,348
    mark tomlinson
    mark tomlinson
    Jan 7, 2018
  6. joea

    Partial Answer My X and Y steps/mm need to be 160 not 80?

    joea, May 15, 2020
    Replies:
    1
    Views:
    783
    mark tomlinson
    mark tomlinson
    May 15, 2020
  7. Theresa

    Partial Answer My Robo R1 Plus is printing, but it sorta skips around

    Theresa, Dec 8, 2017
    Replies:
    10
    Views:
    1,690
    mark tomlinson
    mark tomlinson
    Dec 9, 2017
  8. Kian Ghassemian

    Partial Answer My R1 is stopping after callibration

    Kian Ghassemian, Feb 27, 2019
    Replies:
    2
    Views:
    646
    mark tomlinson
    mark tomlinson
    Feb 28, 2019
  9. Brad Whitmoyer

    Partial Answer movements and speed doubled

    Brad Whitmoyer, Dec 18, 2018
    Replies:
    19
    Views:
    1,481
    Geof
    Geof
    Dec 19, 2018
  10. Dan McCreary
    Locked

    Partial Answer MatterControl will not run on macOS Mojave 10.14.3

    Dan McCreary, Mar 7, 2019
    Replies:
    1
    Views:
    943
    WheresWaldo
    WheresWaldo
    Mar 8, 2019
  11. infinigrove

    Partial Answer Matter Control 1.5 Z Gap option for supports?

    infinigrove, Apr 6, 2016
    Replies:
    14
    Views:
    2,795
    infinigrove
    infinigrove
    Apr 8, 2016
  12. Mr Wire

    Partial Answer mac power settings script to print

    Mr Wire, Nov 6, 2017
    Replies:
    7
    Views:
    893
    WheresWaldo
    WheresWaldo
    Nov 7, 2017
  13. David Avila

    Partial Answer lines on prints

    David Avila, Feb 22, 2018
    Replies:
    7
    Views:
    1,324
    mark tomlinson
    mark tomlinson
    Mar 20, 2018
  14. Domenic

    Partial Answer Layer lines on my prints are not even

    Domenic, Nov 22, 2018 ... 2
    Replies:
    36
    Views:
    4,051
    TheOneWhoWhelms
    TheOneWhoWhelms
    Feb 1, 2019
  15. Lasse Knudsen

    Partial Answer Jagging on filament

    Lasse Knudsen, Aug 12, 2016
    Replies:
    6
    Views:
    1,053
    Lasse Knudsen
    Lasse Knudsen
    Aug 14, 2016
  16. Jerry Normandin

    Partial Answer I have to unclog the extruder just about every time I change the filament.

    Jerry Normandin, Feb 3, 2018
    Replies:
    6
    Views:
    1,510
    Geof
    Geof
    Feb 5, 2018
  17. WheresWaldo

    Partial Answer I am trying to get the sizing correct, suggestions please.

    WheresWaldo, Jun 5, 2015
    Replies:
    9
    Views:
    1,488
    WheresWaldo
    WheresWaldo
    Jun 8, 2015
  18. SergeantPepper

    Partial Answer How to identify your Robo3D printer:

    SergeantPepper, Mar 30, 2015
    Replies:
    1
    Views:
    739
    Mike Kelly
    Mike Kelly
    Mar 30, 2015
  19. Gripp

    Partial Answer Hotend Turns off after autolevel

    Gripp, Aug 8, 2017
    Replies:
    9
    Views:
    1,772
    mark tomlinson
    mark tomlinson
    Aug 11, 2017
  20. Jesse Bartman

    Partial Answer Hotend can't keep up???

    Jesse Bartman, Aug 19, 2017
    Replies:
    2
    Views:
    612
    mark tomlinson
    mark tomlinson
    Aug 19, 2017
Showing threads 61 to 80 of 113

Thread Display Options

Loading...
Page 4 of 6