1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 5 of 26

Filters:

Prefix:
Unanswered x
Remove All Filters:
x
Sort by:
Title ↓ Start Date
Replies Views
Last Message
  1. nikbrewer

    Unanswered Under Extruding?

    nikbrewer, Mar 5, 2015
    Replies:
    4
    Views:
    1,324
    Mike Kelly
    Mike Kelly
    Mar 10, 2015
  2. Lunchbox

    Unanswered Unable to setup Robo3D printer driver

    Lunchbox, Nov 10, 2015
    Replies:
    5
    Views:
    1,011
    Mike Kelly
    Mike Kelly
    Nov 10, 2015
  3. iandroo888

    Unanswered Trying to calibrate printer and print correctly

    iandroo888, Apr 19, 2020 ... 2
    Replies:
    37
    Views:
    3,130
    mark tomlinson
    mark tomlinson
    Apr 21, 2020
  4. Teamjynx

    Unanswered Tray bed not moving

    Teamjynx, Jun 20, 2015
    Replies:
    3
    Views:
    627
    daniel871
    daniel871
    Jun 22, 2015
  5. Rohan

    Unanswered Tracking Number Never Came, only confirmation email and still don't know when it's coming

    Rohan, Dec 28, 2015
    Replies:
    5
    Views:
    563
    Trama
    Trama
    Dec 28, 2015
  6. Oisin

    Unanswered Top surface holes.

    Oisin, Sep 21, 2015
    Replies:
    3
    Views:
    539
    Mike Kelly
    Mike Kelly
    Sep 21, 2015
  7. Kingbob

    Unanswered Too hot?

    Kingbob, Mar 12, 2017
    Replies:
    0
    Views:
    687
    Kingbob
    Kingbob
    Mar 12, 2017
  8. PACNOR RC AEROSYSTEMS

    Unanswered Tolerance on Z-Axis is off.

    PACNOR RC AEROSYSTEMS, Apr 12, 2016
    Replies:
    4
    Views:
    1,119
    WheresWaldo
    WheresWaldo
    Apr 20, 2016
  9. Robert Choban
    Locked

    Unanswered TIming belt question

    Robert Choban, Dec 2, 2014
    Replies:
    1
    Views:
    846
    Mike Kelly
    Mike Kelly
    Dec 2, 2014
  10. Joseph D.

    Unanswered Threaded Rod is not being held at its round base clamp, loses calibration. What tape(?)etc is needed

    Joseph D., Sep 26, 2016
    Replies:
    1
    Views:
    558
    mark tomlinson
    mark tomlinson
    Sep 26, 2016
  11. Steven Barber

    Unanswered THIS PRINTER IS JUNK!

    Steven Barber, Jul 24, 2016
    Replies:
    12
    Views:
    1,362
    Ryan TeGantvoort
    Ryan TeGantvoort
    Jul 26, 2016
  12. Nathan Simers

    Unanswered The block on my hot end is moving just a bit

    Nathan Simers, Feb 29, 2016
    Replies:
    3
    Views:
    644
    mark tomlinson
    mark tomlinson
    Feb 29, 2016
  13. Oisin

    Unanswered Terrible quality prints.

    Oisin, Sep 5, 2015
    Replies:
    5
    Views:
    721
    Kevin Nguyen
    Kevin Nguyen
    Sep 12, 2015
  14. 90AWDeclipse

    Unanswered Temps freeze during leveling then Error

    90AWDeclipse, Mar 22, 2016 ... 2
    Replies:
    21
    Views:
    3,531
    Zdot
    Zdot
    Mar 25, 2016
  15. Abunai264

    Unanswered Temp Drop Error after Auto-Level

    Abunai264, Dec 6, 2015
    Replies:
    4
    Views:
    689
    Mike Kelly
    Mike Kelly
    Dec 8, 2015
  16. Island Bill

    Unanswered Taulman T-Glase diameter inconsistent?

    Island Bill, Jul 19, 2015
    Replies:
    7
    Views:
    633
    Island Bill
    Island Bill
    Jul 19, 2015
  17. Zen

    Unanswered taulman 910 underextruding at points

    Zen, Sep 22, 2015
    Replies:
    4
    Views:
    510
    Zen
    Zen
    Sep 22, 2015
  18. Curgon

    Unanswered T-Glase not sticking

    Curgon, Mar 22, 2016 ... 2
    Replies:
    35
    Views:
    5,193
    Kristin B
    Kristin B
    Apr 11, 2016
  19. moelafi

    Unanswered surface print layer curling up

    moelafi, Mar 30, 2017
    Replies:
    8
    Views:
    1,783
    mark tomlinson
    mark tomlinson
    Apr 1, 2017
  20. sofiadragon1979

    Unanswered Support material question

    sofiadragon1979, Jan 11, 2015
    Replies:
    11
    Views:
    2,053
    jbigler1986
    jbigler1986
    May 11, 2015
Showing threads 81 to 100 of 514

Thread Display Options

Loading...
Page 5 of 26