1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 21 of 26

Filters:

Prefix:
Answered x
Remove All Filters:
x
Sort by:
Title Start Date ↓
Replies Views
Last Message
  1. Arthur Smith

    Answered Wiring help for Adrino after E3D V6 upgrade

    Arthur Smith, Mar 10, 2016
    Replies:
    10
    Views:
    1,401
    mark tomlinson
    mark tomlinson
    Mar 10, 2016
  2. jcman1990

    Answered Thermistor Wires broke

    jcman1990, Mar 9, 2016
    Replies:
    6
    Views:
    1,753
    robert sanchez
    robert sanchez
    Mar 9, 2016
  3. I Need Help

    Answered Z axis on ROBO 3D R1 printer is starting print way too high

    I Need Help, Mar 8, 2016
    Replies:
    4
    Views:
    2,051
    I Need Help
    I Need Help
    Apr 4, 2016
  4. Dr. Jack Hirschberg

    Answered Help for a newbie...printer won't home properly

    Dr. Jack Hirschberg, Feb 26, 2016
    Replies:
    3
    Views:
    1,159
    mark tomlinson
    mark tomlinson
    Feb 26, 2016
  5. Jimmy Husain

    Answered Overhang?

    Jimmy Husain, Feb 25, 2016
    Replies:
    8
    Views:
    1,727
    Jimmy Husain
    Jimmy Husain
    Feb 26, 2016
  6. artmonkee8
    Locked

    Answered Troubleshooting Y axis shifting

    artmonkee8, Feb 18, 2016
    Replies:
    19
    Views:
    3,334
    mark tomlinson
    mark tomlinson
    Jul 4, 2016
  7. Rusty

    Answered R1 - Z Axis sensor always triggered

    Rusty, Feb 16, 2016
    Replies:
    9
    Views:
    1,440
    mark tomlinson
    mark tomlinson
    Feb 17, 2016
  8. Kreativekris

    Answered Basic questions for after printing (1st print)

    Kreativekris, Feb 16, 2016
    Replies:
    5
    Views:
    1,055
    LumpyDVC
    LumpyDVC
    Feb 16, 2016
  9. Drmike

    Answered Power supply or overheating?

    Drmike, Feb 15, 2016
    Replies:
    13
    Views:
    2,170
    Geof
    Geof
    Apr 10, 2016
  10. nol b

    Answered Print Bed Stopped Heating

    nol b, Feb 12, 2016 ... 2
    Replies:
    20
    Views:
    3,785
    mark tomlinson
    mark tomlinson
    Nov 19, 2019
  11. MOwens5150

    Answered Wire harness issue

    MOwens5150, Jan 30, 2016
    Replies:
    5
    Views:
    1,314
    MOwens5150
    MOwens5150
    Feb 2, 2016
  12. Taylor

    Answered Lines in Prints

    Taylor, Jan 29, 2016
    Replies:
    6
    Views:
    1,330
    Taylor
    Taylor
    Jan 30, 2016
  13. JuanPinto

    Answered WIRES CROSSED?

    JuanPinto, Jan 19, 2016
    Replies:
    5
    Views:
    724
    mark tomlinson
    mark tomlinson
    Jan 21, 2016
  14. Travis M

    Answered Print Quality Not Very Good

    Travis M, Jan 2, 2016
    Replies:
    18
    Views:
    1,259
    Geof
    Geof
    Jan 3, 2016
  15. paulishuku

    Answered Y Axis Center Point off by Approx 1 Inch Robo 3D R1+

    paulishuku, Jan 1, 2016
    Replies:
    4
    Views:
    600
    paulishuku
    paulishuku
    Jan 1, 2016
  16. wthierry

    Answered Leadscrew firmware updated, but look what it does...

    wthierry, Dec 30, 2015
    Replies:
    13
    Views:
    1,596
    mark tomlinson
    mark tomlinson
    Jan 3, 2016
  17. Marquis Johnson

    Answered Useful G-Codes You Should Know

    Marquis Johnson, Dec 30, 2015
    Replies:
    4
    Views:
    790
    Marquis Johnson
    Marquis Johnson
    Dec 31, 2015
  18. Jimmy Husain

    Answered How Can I Improve This? Part IV

    Jimmy Husain, Dec 15, 2015
    Replies:
    6
    Views:
    474
    Jimmy Husain
    Jimmy Husain
    Dec 15, 2015
  19. robert sanchez

    Answered Heater failure

    robert sanchez, Dec 14, 2015
    Replies:
    17
    Views:
    783
    robert sanchez
    robert sanchez
    Dec 22, 2015
  20. Jimmy Husain

    Answered How Can I Improve This? Part III

    Jimmy Husain, Dec 12, 2015
    Replies:
    6
    Views:
    711
    Mike Kelly
    Mike Kelly
    Dec 16, 2015
Showing threads 401 to 420 of 511

Thread Display Options

Loading...
Page 21 of 26