1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Page 21 of 28
Sort by:
Title Start Date
Replies Views
Last Message ↑
  1. Eric Viglotti

    Dried Spaghetti on bottom layer but then fine for all other layers

    Eric Viglotti, Dec 8, 2019 ... 2
    Replies:
    20
    Views:
    2,814
    adikted2astro
    adikted2astro
    Dec 21, 2019
  2. studiver13
    Locked

    Connection Interrupted

    studiver13, Dec 22, 2019 ... 2 3
    Replies:
    43
    Views:
    4,823
    mark tomlinson
    mark tomlinson
    Dec 26, 2019
  3. adikted2astro

    Vase Mode Leaving Voids in Sliced Models

    adikted2astro, Dec 10, 2019
    Replies:
    12
    Views:
    1,404
    mark tomlinson
    mark tomlinson
    Dec 28, 2019
  4. Joseph Everhart

    Ribbon cable pinouts

    Joseph Everhart, Dec 29, 2019
    Replies:
    2
    Views:
    740
    Joseph Everhart
    Joseph Everhart
    Dec 29, 2019
  5. Paul1967

    Heater is not found error

    Paul1967, Dec 26, 2019
    Replies:
    10
    Views:
    1,092
    WheresWaldo
    WheresWaldo
    Jan 1, 2020
  6. Clay Raber

    Z Axis moves upward during Fine Tune Wizard

    Clay Raber, Jan 8, 2020
    Replies:
    4
    Views:
    886
    Clay Raber
    Clay Raber
    Jan 9, 2020
  7. BJS227

    help with first layer on section of bed

    BJS227, Jan 8, 2020
    Replies:
    2
    Views:
    737
    tkoco
    tkoco
    Jan 10, 2020
  8. MGF

    Used Robo R2 missing parts

    MGF, Jan 3, 2020 ... 2
    Replies:
    20
    Views:
    2,774
    MGF
    MGF
    Jan 20, 2020
  9. VigilantWookie
    Locked

    Touchscreen Issue

    VigilantWookie, Feb 7, 2020
    Replies:
    3
    Views:
    851
    tkoco
    tkoco
    Feb 8, 2020
  10. erickbeebe58

    Printer out of control

    erickbeebe58, Feb 6, 2020
    Replies:
    5
    Views:
    930
    tkoco
    tkoco
    Feb 8, 2020
  11. Lang Schwartzwald

    Z-offset issue

    Lang Schwartzwald, Feb 10, 2020
    Replies:
    2
    Views:
    700
    tkoco
    tkoco
    Feb 11, 2020
  12. Matthew P

    Z Offset Wizard Stopping at Step 1/4 with bed around 40mm away from extruding tip

    Matthew P, Feb 11, 2020
    Replies:
    5
    Views:
    1,085
    tkoco
    tkoco
    Feb 11, 2020
  13. Matthew P

    R2 Not showing files on flash drive

    Matthew P, Feb 12, 2020
    Replies:
    2
    Views:
    716
    tkoco
    tkoco
    Feb 13, 2020
  14. VigilantWookie

    Bed Leveling

    VigilantWookie, Feb 14, 2020
    Replies:
    3
    Views:
    848
    WheresWaldo
    WheresWaldo
    Feb 19, 2020
  15. VigilantWookie

    New Owner-Print Edges curling early in print

    VigilantWookie, Feb 6, 2020
    Replies:
    6
    Views:
    977
    VigilantWookie
    VigilantWookie
    Feb 19, 2020
  16. wford

    Heat Bed Failed Error

    wford, Feb 19, 2020
    Replies:
    7
    Views:
    965
    mark tomlinson
    mark tomlinson
    Feb 20, 2020
  17. Kris Karlsson

    Print Bed V2 Issue

    Kris Karlsson, Feb 19, 2020
    Replies:
    3
    Views:
    652
    mark tomlinson
    mark tomlinson
    Feb 20, 2020
  18. VigilantWookie

    Print Stuck

    VigilantWookie, Feb 21, 2020
    Replies:
    2
    Views:
    692
    VigilantWookie
    VigilantWookie
    Feb 21, 2020
  19. Thomas Strickland

    Robo r2

    Thomas Strickland, Mar 7, 2020
    Replies:
    2
    Views:
    806
    tkoco
    tkoco
    Mar 8, 2020
  20. Jimbobikr

    Hotend Thermister Issues

    Jimbobikr, Mar 13, 2020
    Replies:
    17
    Views:
    1,618
    mark tomlinson
    mark tomlinson
    Mar 15, 2020
Showing threads 401 to 420 of 545

Thread Display Options

Loading...
Page 21 of 28