1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 1 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title Start Date
Replies ↑ Views
Last Message
  1. joea

    Partial Answer My X and Y steps/mm need to be 160 not 80?

    joea, May 15, 2020
    Replies:
    1
    Views:
    783
    mark tomlinson
    mark tomlinson
    May 15, 2020
  2. CCJ

    Partial Answer Firmware Nonresponsive

    CCJ, Sep 15, 2019
    Replies:
    1
    Views:
    694
    mark tomlinson
    mark tomlinson
    Sep 16, 2019
  3. Dannny18

    Partial Answer Trouble with printing

    Dannny18, Sep 2, 2019
    Replies:
    1
    Views:
    686
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  4. mindphunk

    Partial Answer Cooling Issue?

    mindphunk, Jul 30, 2019
    Replies:
    1
    Views:
    714
    mark tomlinson
    mark tomlinson
    Jul 31, 2019
  5. Dan McCreary
    Locked

    Partial Answer MatterControl will not run on macOS Mojave 10.14.3

    Dan McCreary, Mar 7, 2019
    Replies:
    1
    Views:
    945
    WheresWaldo
    WheresWaldo
    Mar 8, 2019
  6. Mark Ostrander

    Partial Answer printer stops ...unable to communicate with printer

    Mark Ostrander, Feb 27, 2019
    Replies:
    1
    Views:
    585
    mark tomlinson
    mark tomlinson
    Feb 27, 2019
  7. Bd182

    Partial Answer Soft edges, higher than the center

    Bd182, Feb 19, 2019
    Replies:
    1
    Views:
    533
    Geof
    Geof
    Feb 19, 2019
  8. John in MS

    Partial Answer Problems after installing E3DV6

    John in MS, May 29, 2018
    Replies:
    1
    Views:
    685
    mark tomlinson
    mark tomlinson
    May 30, 2018
  9. Skivholme

    Partial Answer Problem when prints get "high"

    Skivholme, Feb 26, 2018
    Replies:
    1
    Views:
    654
    WheresWaldo
    WheresWaldo
    Feb 26, 2018
  10. Kay Liu

    Partial Answer After printing, right and left side not at same level

    Kay Liu, Oct 24, 2017
    Replies:
    1
    Views:
    644
    Geof
    Geof
    Oct 24, 2017
  11. Will . I . Am

    Partial Answer Upgrade to v.2 firmware? How to get FULL graphics smart lcd screen to work etc..

    Will . I . Am, Feb 7, 2017
    Replies:
    1
    Views:
    1,207
    mark tomlinson
    mark tomlinson
    Feb 8, 2017
  12. Omar157

    Partial Answer Need some help with E3d v6 upgrade

    Omar157, Feb 7, 2017
    Replies:
    1
    Views:
    630
    Geof
    Geof
    Feb 7, 2017
  13. xHOBOPHOBIAx

    Partial Answer X Axis stepper stuttering when moved by hand.

    xHOBOPHOBIAx, Feb 6, 2017
    Replies:
    1
    Views:
    600
    mark tomlinson
    mark tomlinson
    Feb 7, 2017
  14. momoe

    Partial Answer Whole hot end and heatsync are loose

    momoe, Feb 6, 2017
    Replies:
    1
    Views:
    717
    mark tomlinson
    mark tomlinson
    Feb 7, 2017
  15. Agrijag

    Partial Answer Need help finishing extruder swap

    Agrijag, Jan 28, 2017
    Replies:
    1
    Views:
    739
    mark tomlinson
    mark tomlinson
    Jan 28, 2017
  16. SergeantPepper

    Partial Answer How to identify your Robo3D printer:

    SergeantPepper, Mar 30, 2015
    Replies:
    1
    Views:
    740
    Mike Kelly
    Mike Kelly
    Mar 30, 2015
  17. Russ_B

    Partial Answer Firmware Recommendation

    Russ_B, Sep 25, 2022
    Replies:
    2
    Views:
    711
    Russ_B
    Russ_B
    Sep 27, 2022
  18. Daniel Flores

    Partial Answer Filament not entering extruder

    Daniel Flores, Sep 2, 2019
    Replies:
    2
    Views:
    829
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  19. robert albrecht

    Partial Answer Ughhhh I am back... MC not printing support strucures

    robert albrecht, Aug 21, 2019
    Replies:
    2
    Views:
    803
    BrooklynBay
    BrooklynBay
    Aug 22, 2019
  20. felipe fomez

    Partial Answer rods bent???

    felipe fomez, Mar 28, 2019
    Replies:
    2
    Views:
    862
    Geof
    Geof
    Mar 29, 2019
Showing threads 1 to 20 of 113

Thread Display Options

Loading...
Page 1 of 6