1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 5 of 26

Filters:

Prefix:
Answered x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views
Last Message ↑
  1. Chavezj23

    Answered Extruder upgrade (R1 Plus)

    Chavezj23, Nov 15, 2015
    Replies:
    5
    Views:
    1,644
    Mike Kelly
    Mike Kelly
    Nov 16, 2015
  2. wthierry

    Answered Wow! what a difference "SEASONING" makes!

    wthierry, Feb 1, 2015 ... 2
    Replies:
    21
    Views:
    2,991
    mikejsmith1985
    mikejsmith1985
    Nov 24, 2015
  3. Marquis Johnson

    Answered Video Guide: Electrical System

    Marquis Johnson, Nov 19, 2015
    Replies:
    3
    Views:
    944
    Luis Olivet
    Luis Olivet
    Nov 27, 2015
  4. Jcastor

    Answered Issue homing axes, x axis doesn't stop and grinds

    Jcastor, Nov 29, 2015
    Replies:
    8
    Views:
    2,282
    mark tomlinson
    mark tomlinson
    Nov 29, 2015
  5. Michael S

    Answered Is it necessary to print a border?

    Michael S, Dec 1, 2015
    Replies:
    3
    Views:
    619
    Michael S
    Michael S
    Dec 1, 2015
  6. Central Utah 3D

    Answered Printer just stops

    Central Utah 3D, Nov 5, 2015
    Replies:
    13
    Views:
    1,453
    Trama
    Trama
    Dec 12, 2015
  7. Jimmy Husain

    Answered How Can I Improve This? Part IV

    Jimmy Husain, Dec 15, 2015
    Replies:
    6
    Views:
    472
    Jimmy Husain
    Jimmy Husain
    Dec 15, 2015
  8. Jimmy Husain

    Answered How Can I Improve This? Part III

    Jimmy Husain, Dec 12, 2015
    Replies:
    6
    Views:
    708
    Mike Kelly
    Mike Kelly
    Dec 16, 2015
  9. robert sanchez

    Answered Heater failure

    robert sanchez, Dec 14, 2015
    Replies:
    17
    Views:
    781
    robert sanchez
    robert sanchez
    Dec 22, 2015
  10. Marquis Johnson

    Answered Useful G-Codes You Should Know

    Marquis Johnson, Dec 30, 2015
    Replies:
    4
    Views:
    790
    Marquis Johnson
    Marquis Johnson
    Dec 31, 2015
  11. paulishuku

    Answered Y Axis Center Point off by Approx 1 Inch Robo 3D R1+

    paulishuku, Jan 1, 2016
    Replies:
    4
    Views:
    597
    paulishuku
    paulishuku
    Jan 1, 2016
  12. wthierry

    Answered Leadscrew firmware updated, but look what it does...

    wthierry, Dec 30, 2015
    Replies:
    13
    Views:
    1,593
    mark tomlinson
    mark tomlinson
    Jan 3, 2016
  13. Travis M

    Answered Print Quality Not Very Good

    Travis M, Jan 2, 2016
    Replies:
    18
    Views:
    1,259
    Geof
    Geof
    Jan 3, 2016
  14. JuanPinto

    Answered WIRES CROSSED?

    JuanPinto, Jan 19, 2016
    Replies:
    5
    Views:
    723
    mark tomlinson
    mark tomlinson
    Jan 21, 2016
  15. Taylor

    Answered Lines in Prints

    Taylor, Jan 29, 2016
    Replies:
    6
    Views:
    1,330
    Taylor
    Taylor
    Jan 30, 2016
  16. MOwens5150

    Answered Wire harness issue

    MOwens5150, Jan 30, 2016
    Replies:
    5
    Views:
    1,306
    MOwens5150
    MOwens5150
    Feb 2, 2016
  17. Kreativekris

    Answered Basic questions for after printing (1st print)

    Kreativekris, Feb 16, 2016
    Replies:
    5
    Views:
    1,051
    LumpyDVC
    LumpyDVC
    Feb 16, 2016
  18. Rusty

    Answered R1 - Z Axis sensor always triggered

    Rusty, Feb 16, 2016
    Replies:
    9
    Views:
    1,432
    mark tomlinson
    mark tomlinson
    Feb 17, 2016
  19. Dr. Jack Hirschberg

    Answered Help for a newbie...printer won't home properly

    Dr. Jack Hirschberg, Feb 26, 2016
    Replies:
    3
    Views:
    1,155
    mark tomlinson
    mark tomlinson
    Feb 26, 2016
  20. Jimmy Husain

    Answered Overhang?

    Jimmy Husain, Feb 25, 2016
    Replies:
    8
    Views:
    1,724
    Jimmy Husain
    Jimmy Husain
    Feb 26, 2016
Showing threads 81 to 100 of 511

Thread Display Options

Loading...
Page 5 of 26