1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 5 of 26

Filters:

Prefix:
Answered x
Remove All Filters:
x
Sort by:
Title Start Date ↑
Replies Views
Last Message
  1. jediknight0

    Answered cork pulling away from heated bed

    jediknight0, Aug 29, 2015
    Replies:
    8
    Views:
    780
    danzca6
    danzca6
    Sep 1, 2015
  2. Tony Bucci

    Answered Heatbed Solid State relay replacement issues

    Tony Bucci, Aug 30, 2015
    Replies:
    2
    Views:
    497
    mark tomlinson
    mark tomlinson
    Aug 30, 2015
  3. janot928

    Answered printer not heating (fuse?)

    janot928, Sep 2, 2015
    Replies:
    14
    Views:
    1,052
    janot928
    janot928
    Sep 4, 2015
  4. wthierry

    Answered after calibrating E still printing problems persist

    wthierry, Oct 11, 2015
    Replies:
    12
    Views:
    841
    wthierry
    wthierry
    Oct 20, 2015
  5. Jimmy Husain

    Answered What Is This?

    Jimmy Husain, Oct 27, 2015
    Replies:
    15
    Views:
    926
    Mike Kelly
    Mike Kelly
    Oct 29, 2015
  6. Central Utah 3D

    Answered Printer just stops

    Central Utah 3D, Nov 5, 2015
    Replies:
    13
    Views:
    1,455
    Trama
    Trama
    Dec 12, 2015
  7. RoboRage

    Answered Corkboard sagging

    RoboRage, Nov 6, 2015
    Replies:
    2
    Views:
    562
    RoboRage
    RoboRage
    Nov 6, 2015
  8. Chavezj23

    Answered Extruder upgrade (R1 Plus)

    Chavezj23, Nov 15, 2015
    Replies:
    5
    Views:
    1,647
    Mike Kelly
    Mike Kelly
    Nov 16, 2015
  9. Marquis Johnson

    Answered Video Guide: Electrical System

    Marquis Johnson, Nov 19, 2015
    Replies:
    3
    Views:
    947
    Luis Olivet
    Luis Olivet
    Nov 27, 2015
  10. Jcastor

    Answered Issue homing axes, x axis doesn't stop and grinds

    Jcastor, Nov 29, 2015
    Replies:
    8
    Views:
    2,289
    mark tomlinson
    mark tomlinson
    Nov 29, 2015
  11. Michael S

    Answered Is it necessary to print a border?

    Michael S, Dec 1, 2015
    Replies:
    3
    Views:
    620
    Michael S
    Michael S
    Dec 1, 2015
  12. Jimmy Husain

    Answered How Can I Improve This? Part III

    Jimmy Husain, Dec 12, 2015
    Replies:
    6
    Views:
    712
    Mike Kelly
    Mike Kelly
    Dec 16, 2015
  13. robert sanchez

    Answered Heater failure

    robert sanchez, Dec 14, 2015
    Replies:
    17
    Views:
    783
    robert sanchez
    robert sanchez
    Dec 22, 2015
  14. Jimmy Husain

    Answered How Can I Improve This? Part IV

    Jimmy Husain, Dec 15, 2015
    Replies:
    6
    Views:
    475
    Jimmy Husain
    Jimmy Husain
    Dec 15, 2015
  15. Marquis Johnson

    Answered Useful G-Codes You Should Know

    Marquis Johnson, Dec 30, 2015
    Replies:
    4
    Views:
    792
    Marquis Johnson
    Marquis Johnson
    Dec 31, 2015
  16. wthierry

    Answered Leadscrew firmware updated, but look what it does...

    wthierry, Dec 30, 2015
    Replies:
    13
    Views:
    1,597
    mark tomlinson
    mark tomlinson
    Jan 3, 2016
  17. paulishuku

    Answered Y Axis Center Point off by Approx 1 Inch Robo 3D R1+

    paulishuku, Jan 1, 2016
    Replies:
    4
    Views:
    601
    paulishuku
    paulishuku
    Jan 1, 2016
  18. Travis M

    Answered Print Quality Not Very Good

    Travis M, Jan 2, 2016
    Replies:
    18
    Views:
    1,260
    Geof
    Geof
    Jan 3, 2016
  19. JuanPinto

    Answered WIRES CROSSED?

    JuanPinto, Jan 19, 2016
    Replies:
    5
    Views:
    725
    mark tomlinson
    mark tomlinson
    Jan 21, 2016
  20. Taylor

    Answered Lines in Prints

    Taylor, Jan 29, 2016
    Replies:
    6
    Views:
    1,331
    Taylor
    Taylor
    Jan 30, 2016
Showing threads 81 to 100 of 511

Thread Display Options

Loading...
Page 5 of 26