1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 88 of 94

Filters:

Prefix:
Solved x
Remove All Filters:
x
Sort by:
Title Start Date ↓
Replies Views
Last Message
  1. Tanbam
    Locked

    Solved How do I remove the power supply?

    Tanbam, Feb 8, 2015
    Replies:
    4
    Views:
    766
    Ziggy
    Ziggy
    Feb 9, 2015
  2. jwvanno

    Solved Z axis printing too short.

    jwvanno, Feb 8, 2015
    Replies:
    11
    Views:
    11,944
    Vabrik
    Vabrik
    Jul 27, 2015
  3. 1nxtmonster
    Locked

    Solved Z artifacts on one side of print

    1nxtmonster, Feb 8, 2015
    Replies:
    6
    Views:
    778
    1nxtmonster
    1nxtmonster
    Feb 8, 2015
  4. Island Bill

    Solved RAMPS board, LED2 shows intermittent cutout of voltage.

    Island Bill, Feb 8, 2015
    Replies:
    19
    Views:
    5,271
    mark tomlinson
    mark tomlinson
    Apr 21, 2017
  5. Ozzy

    Solved Increasing Print Bed (Platen) Temperature

    Ozzy, Feb 6, 2015
    Replies:
    5
    Views:
    1,588
    Apel Papa
    Apel Papa
    Apr 19, 2016
  6. k1e1v1i1n
    Locked

    Solved I have developed a bit of a wobble.

    k1e1v1i1n, Feb 5, 2015
    Replies:
    11
    Views:
    688
    mark tomlinson
    mark tomlinson
    Feb 6, 2015
  7. Ben R
    Locked

    Solved temp fall error trouble shooting

    Ben R, Feb 5, 2015 ... 2
    Replies:
    22
    Views:
    4,451
    mark tomlinson
    mark tomlinson
    Jan 9, 2018
  8. bryson bishop
    Locked

    Solved Extruder will not go low enough

    bryson bishop, Feb 4, 2015
    Replies:
    10
    Views:
    1,063
    Ben R
    Ben R
    Feb 4, 2015
  9. Stephen Capistron
    Locked

    Solved Everything is a little big or under filled

    Stephen Capistron, Feb 4, 2015
    Replies:
    14
    Views:
    728
    Printed Solid
    Printed Solid
    Feb 7, 2015
  10. Ben R
    Locked

    Solved This is what happens when your z rods fall out of alignment.

    Ben R, Feb 3, 2015
    Replies:
    3
    Views:
    554
    Ben R
    Ben R
    Feb 4, 2015
  11. LabMinion

    Solved Lifting edge and dragging nozzle across bed

    LabMinion, Feb 3, 2015 ... 2 3
    Replies:
    46
    Views:
    11,070
    Mike Kelly
    Mike Kelly
    Oct 21, 2015
  12. Taylor
    Locked

    Solved Temp Fall Error =(

    Taylor, Feb 3, 2015
    Replies:
    15
    Views:
    871
    Ben R
    Ben R
    Feb 4, 2015
  13. BrianAnim
    Locked

    Solved Bed won't heat

    BrianAnim, Feb 2, 2015
    Replies:
    2
    Views:
    926
    Mike Kelly
    Mike Kelly
    Feb 3, 2015
  14. anmael
    Locked

    Solved Robo3d R1 Cannot print under 200degrees

    anmael, Feb 1, 2015
    Replies:
    4
    Views:
    650
    anmael
    anmael
    Feb 1, 2015
  15. robert sanchez
    Locked

    Solved Where to connect the ramps cooling fan

    robert sanchez, Jan 31, 2015
    Replies:
    2
    Views:
    1,188
    robert sanchez
    robert sanchez
    Jan 31, 2015
  16. davmad
    Locked

    Solved Filament getting stuck in extruder

    davmad, Jan 30, 2015
    Replies:
    16
    Views:
    2,225
    davmad
    davmad
    Feb 1, 2015
  17. YellowMenace

    Solved Top of cylinder didn't seal

    YellowMenace, Jan 28, 2015
    Replies:
    13
    Views:
    805
    YellowMenace
    YellowMenace
    Feb 18, 2015
  18. Jokerk
    Locked

    Solved solid layers breaking open

    Jokerk, Jan 28, 2015 ... 2
    Replies:
    22
    Views:
    1,784
    mark tomlinson
    mark tomlinson
    Feb 7, 2015
  19. wthierry
    Locked

    Solved Bought simplify3d, a couple questions...

    wthierry, Jan 25, 2015
    Replies:
    12
    Views:
    661
    wthierry
    wthierry
    Feb 2, 2015
  20. Chris A

    Solved Extruder Thermistor Fail (née: Heated Bed Failure)

    Chris A, Jan 24, 2015 ... 2 3
    Replies:
    59
    Views:
    6,816
    Mike Kelly
    Mike Kelly
    Jul 9, 2015
Showing threads 1,741 to 1,760 of 1,863

Thread Display Options

Loading...
Page 88 of 94