1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 1 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views ↑
Last Message
  1. Bd182

    Partial Answer Soft edges, higher than the center

    Bd182, Feb 19, 2019
    Replies:
    1
    Views:
    533
    Geof
    Geof
    Feb 19, 2019
  2. Mark Ostrander

    Partial Answer printer stops ...unable to communicate with printer

    Mark Ostrander, Feb 27, 2019
    Replies:
    1
    Views:
    585
    mark tomlinson
    mark tomlinson
    Feb 27, 2019
  3. Kort Jurgensmeyer

    Partial Answer filament extrusion

    Kort Jurgensmeyer, Nov 5, 2017
    Replies:
    2
    Views:
    585
    Geof
    Geof
    Nov 6, 2017
  4. scott treichler

    Partial Answer stepper motor for extruder will not run during print, works from control panel in software

    scott treichler, Feb 4, 2017
    Replies:
    2
    Views:
    591
    mark tomlinson
    mark tomlinson
    Feb 7, 2017
  5. xHOBOPHOBIAx

    Partial Answer X Axis stepper stuttering when moved by hand.

    xHOBOPHOBIAx, Feb 6, 2017
    Replies:
    1
    Views:
    600
    mark tomlinson
    mark tomlinson
    Feb 7, 2017
  6. Jesse Bartman

    Partial Answer Hotend can't keep up???

    Jesse Bartman, Aug 19, 2017
    Replies:
    2
    Views:
    616
    mark tomlinson
    mark tomlinson
    Aug 19, 2017
  7. mike2017

    Partial Answer printer is not going side to side

    mike2017, Apr 14, 2018
    Replies:
    2
    Views:
    618
    mark tomlinson
    mark tomlinson
    Apr 14, 2018
  8. Omar157

    Partial Answer Need some help with E3d v6 upgrade

    Omar157, Feb 7, 2017
    Replies:
    1
    Views:
    630
    Geof
    Geof
    Feb 7, 2017
  9. eastmade75

    Partial Answer R1+ bed heater issue

    eastmade75, Mar 21, 2018
    Replies:
    2
    Views:
    633
    eastmade75
    eastmade75
    Mar 22, 2018
  10. Kay Liu

    Partial Answer After printing, right and left side not at same level

    Kay Liu, Oct 24, 2017
    Replies:
    1
    Views:
    644
    Geof
    Geof
    Oct 24, 2017
  11. Kian Ghassemian

    Partial Answer My R1 is stopping after callibration

    Kian Ghassemian, Feb 27, 2019
    Replies:
    2
    Views:
    649
    mark tomlinson
    mark tomlinson
    Feb 28, 2019
  12. Skivholme

    Partial Answer Problem when prints get "high"

    Skivholme, Feb 26, 2018
    Replies:
    1
    Views:
    655
    WheresWaldo
    WheresWaldo
    Feb 26, 2018
  13. lutherus

    Partial Answer No extruding first layers after firmware update

    lutherus, Feb 3, 2018
    Replies:
    2
    Views:
    683
    WheresWaldo
    WheresWaldo
    Feb 3, 2018
  14. ltlderek

    Partial Answer Print Sliding post-hot end replacement

    ltlderek, Feb 25, 2017
    Replies:
    3
    Views:
    683
    mark tomlinson
    mark tomlinson
    Feb 25, 2017
  15. John in MS

    Partial Answer Problems after installing E3DV6

    John in MS, May 29, 2018
    Replies:
    1
    Views:
    685
    mark tomlinson
    mark tomlinson
    May 30, 2018
  16. Dannny18

    Partial Answer Trouble with printing

    Dannny18, Sep 2, 2019
    Replies:
    1
    Views:
    686
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  17. CCJ

    Partial Answer Z Height Issue

    CCJ, Feb 25, 2017
    Replies:
    2
    Views:
    695
    mark tomlinson
    mark tomlinson
    Feb 25, 2017
  18. CCJ

    Partial Answer Firmware Nonresponsive

    CCJ, Sep 15, 2019
    Replies:
    1
    Views:
    695
    mark tomlinson
    mark tomlinson
    Sep 16, 2019
  19. Lance Jimenez

    Partial Answer X and Y axis homing issue

    Lance Jimenez, Jun 16, 2017
    Replies:
    2
    Views:
    696
    Geof
    Geof
    Jun 19, 2017
  20. jasonsummers9

    Partial Answer SD3 and XXL Controller parts cooling fan not turning on

    jasonsummers9, Feb 3, 2018
    Replies:
    3
    Views:
    697
    mark tomlinson
    mark tomlinson
    Feb 4, 2018
Showing threads 1 to 20 of 113

Thread Display Options

Loading...
Page 1 of 6